libraries/AP_Scripting/examples/message_interval.lua - master - Sangak/ardupilot

libraries/AP_Scripting/examples/message_interval.lua
85 строк4 KB
Randy Mackay
AP_Scripting: message_interval gets more messages
19 окт 2025, 10:11
19 окт 2025, 10:1108eaef9
-- This script is an example of manipulating the message stream rates
--
-- It will periodically run and adjust all the messages to their desired loop rates
-- It can be modified to only run once, however some GCS's will manipulate the rates
-- during the initial connection, so by resetting them periodically we ensure we get
-- the expected telemetry rate

local MAV_SEVERITY = {EMERGENCY=0, ALERT=1, CRITICAL=2, ERROR=3, WARNING=4, NOTICE=5, INFO=6, DEBUG=7}

local loop_time = 5000 -- number of ms between runs

-- mavlink message ids
local AHRS_ID                   = uint32_t(163)
local AHRS2_ID                  = uint32_t(178)
local BATTERY_STATUS_ID         = uint32_t(147)
local ATTITUDE_ID               = uint32_t(30)
local DISTANCE_SENSOR_ID        = uint32_t(132)
local EKF_STATUS_REPORT_ID      = uint32_t(193)
local GLOBAL_POSITION_INT_ID    = uint32_t(33)
local GPS_RAW_INT_ID            = uint32_t(24)
--local LOCAL_POSITION_NED_ID     = uint32_t(32)
local NAV_CONTROLLER_OUTPUT_ID  = uint32_t(62)
local POWER_STATUS_ID           = uint32_t(125)
--local RAW_IMU_ID                = uint32_t(27)
--local RC_CHANNELS_ID            = uint32_t(65)
local SERVO_OUTPUT_RAW_ID       = uint32_t(36)
local SYS_STATUS_ID             = uint32_t(1)
--local SYSTEM_TIME_ID            = uint32_t(2)
local TERRAIN_REPORT_ID         = uint32_t(136)
local TERRAIN_REQUEST_ID        = uint32_t(133)
local VFR_HUD_ID                = uint32_t(74)
local VIBRATION_ID              = uint32_t(241)
--local WIND_ID                   = uint32_t(168)
local CAMERA_THERMAL_RANGE_ID   = uint32_t(277)

-- serial port number
-- e.g. SERIAL3 is 3
--      NET_P2 is 22
--      CAN_D2_UC_S3 is 53
-- see https://github.com/ArduPilot/ardupilot/blob/master/libraries/AP_SerialManager/AP_SerialManager_config.h#L67
local serial_port = 0

-- intervals is a table which contains a table for each entry we want to adjust
-- each entry is arranged as {the serial link to adjust, the mavlink message ID, and the broadcast interval in Hz}
local intervals = {{serial_port, ATTITUDE_ID, 2.0}, -- ATTITUDE, 2Hz
                   {serial_port, AHRS_ID, 2.0},     -- AHRS, 2Hz
                   {serial_port, AHRS2_ID, 0},      -- AHRS2, 0hz
                   {serial_port, BATTERY_STATUS_ID, 1},         -- BATTERY_STATUS_ID, 1hz
                   {serial_port, DISTANCE_SENSOR_ID, 1},        -- DISTANCE_SENSOR_ID, 1hz
                   {serial_port, EKF_STATUS_REPORT_ID, 1},      -- EKF_STATUS_REPORT, 1hz
                   {serial_port, GLOBAL_POSITION_INT_ID, 1},    -- GLOBAL_POSITION_INT_ID, 1hz
                   {serial_port, GPS_RAW_INT_ID, 1},            -- GPS_RAW_INT_ID, 1hz
                   {serial_port, NAV_CONTROLLER_OUTPUT_ID, 1},  -- NAV_CONTROLLER_OUTPUT_ID, 1hz
                   {serial_port, POWER_STATUS_ID, 1},           -- POWER_STATUS_ID, 1hz
                   {serial_port, SERVO_OUTPUT_RAW_ID, 1},       -- SERVO_OUTPUT_RAW_ID, 1hz
                   {serial_port, SYS_STATUS_ID, 1},             -- SYS_STATUS_ID, 1hz
                   {serial_port, TERRAIN_REPORT_ID, 1},         -- TERRAIN_REPORT_ID, 1hz
                   {serial_port, TERRAIN_REQUEST_ID, 1},        -- TERRAIN_REQUEST_ID, 1hz
                   {serial_port, VFR_HUD_ID, 1},                -- VFR_HUD_ID, 1hz
                   {serial_port, VIBRATION_ID, 1},              -- VIBRATION_ID, 1hz
                   {serial_port, CAMERA_THERMAL_RANGE_ID, 1},   -- CAMERA_THERMAL_RANGE_ID, 1hz
                  }

-- print welcome message
gcs:send_text(MAV_SEVERITY.INFO, "Loaded message_interval.lua")

function update() -- this is the loop which periodically runs
  for i = 1, #intervals do -- we want to iterate over every specified interval
    local port_num, message, interval_hz = table.unpack(intervals[i]) -- this extracts the port_num, MAVLink ID, and interval

    -- Lua checks get the unpacked types wrong, these are the correct types
    ---@cast port_num integer
    ---@cast message uint32_t_ud
    ---@cast interval_hz number

    local interval_us = -1
    if interval_hz > 0 then
      interval_us = math.floor(1000000 / interval_hz) -- convert the interval to microseconds
    end
    gcs:set_message_interval(port_num, message, interval_us) -- actually sets the interval as appropriate
  end
  return update, loop_time -- reschedules the loop
end

return update() -- run immediately before starting to reschedule