niceSOFT/libssh2: the SSH library

docs/libssh2_sftp_write.3
73 строки3 KB
Daniel Stenberg
libssh2_sftp_write.3: added blurb about the "write ahead"
25 окт 2010, 18:38
25 окт 2010, 18:388e09833
.\" $Id: libssh2_sftp_write.3,v 1.3 2009/03/17 10:34:27 bagder Exp $
.\"
.TH libssh2_sftp_write 3 "1 Jun 2007" "libssh2 0.15" "libssh2 manual"
.SH NAME
libssh2_sftp_write - write SFTP data
.SH SYNOPSIS
.nf
#include <libssh2.h>
#include <libssh2_sftp.h>

ssize_t libssh2_sftp_write(LIBSSH2_SFTP_HANDLE *handle,
                           const char *buffer,
                           size_t count);
.SH DESCRIPTION
\fBlibssh2_sftp_write(3)\fP writes a block of data to the SFTP server. This
method is modeled after the POSIX write() function and uses the same calling
semantics.

\fIhandle\fP - SFTP file handle as returned by \fIlibssh2_sftp_open_ex(3)\fP.

\fIbuffer\fP - points to the data to send off.

\fIcount\fP - Number of bytes from 'buffer' to write. Note that it may not be
possible to write all bytes as requested.

\fIlibssh2_sftp_handle(3)\fP will use as much as possible of the buffer and
put it into a single SFTP protocol packet. This means that to get maximum
performance when sending larger files, you should try to always pass in at
least 32K of data to this function.

.SH WRITE AHEAD
Starting in libssh2 version 1.2.8, the default behavior of libssh2 is to
create several smaller outgoing packets for all data you pass to this function
and it will return a positive number as soon as the first packet is
acknowledged from the server.

This has the effect that sometimes more data has been sent off but isn't acked
yet when this function returns, and when this function is subsequently called
again to write more data, libssh2 will immediately figure out that the data is
already received remotely.

In most normal situation this should not cause any problems, but it should be
noted that if you've once called libssh2_sftp_write() with data and it returns
short, you MUST still assume that the rest of the data might've been cached so
you need to make sure you don't alter that data and think that the version you
have in your next function invoke will be detected or used.

The reason for this funny behavior is that SFTP can only send 32K data in each
packet and it gets all packets acked individually. This means we cannot use a
simple serial approach if we want to reach high performance even on high
latency connections. And we want that.
.SH RETURN VALUE
Actual number of bytes written or negative on failure.

If used in non-blocking mode, it returns LIBSSH2_ERROR_EAGAIN when it would
otherwise block. While LIBSSH2_ERROR_EAGAIN is a negative number, it isn't
really a failure per se.

If this function returns 0 (zero) it should not be considered an error, but
simply that there was no error but yet no payload data got sent to the other
end.
.SH ERRORS
\fILIBSSH2_ERROR_ALLOC\fP -  An internal memory allocation call failed.

\fILIBSSH2_ERROR_SOCKET_SEND\fP - Unable to send data on socket.

\fILIBSSH2_ERROR_SOCKET_TIMEOUT\fP - 

\fILIBSSH2_ERROR_SFTP_PROTOCOL\fP - An invalid SFTP protocol response was 
received on the socket, or an SFTP operation caused an errorcode to 
be returned by the server.
.SH SEE ALSO
.BR libssh2_sftp_open_ex(3)