pcilmr.man - master - githubmirror/pciutils

pcilmr.man
265 строк8 KB
Martin Mareš
Clean up man pages
22 апр 2026, 13:05
22 апр 2026, 13:0541d8078
.TH PCILMR 8 "@TODAY@" "@VERSION@" "The PCI Utilities"
.SH NAME
pcilmr \- margin PCIe Links
.SH SYNOPSIS
.B pcilmr
.RB [ "\-\-margin" ]
.RI [ "<common options>" ] " <link port> " [ "<link options>" "] [" "<link port> " [ "<link options>" ] " ..." ]
.br
.B pcilmr \-\-full
.RI [ "<common options>" ]
.br
.B pcilmr \-\-scan
.SH CONFIGURATION
List of the requirements for links and system settings
to run the margining test.

.B BIOS settings
(depends on the system, relevant for server baseboards
with Xeon CPUs):
.IP \[bu] 3
Turn off PCIe Leaky Bucket Feature, Re-Equalization and Link Degradation;
.IP \[bu]
Set Error Thresholds to 0;
.IP \[bu]
Intel VMD for NVMe SSDs \(en in case of strange behavior of the
.BR pcilmr ,
try to run it with the VMD turned off.
.PP
.B Device (link) requirements:
.IP
.I "Configured by the user before running the utility, the utility does not change them:"
.RS
.IP \[bu] 3
The current Link data rate must be 16.0 GT/s or higher (right now
utility supports 16 GT/s and 32 GT/s Links);
.IP \[bu]
Link Downstream Component must be at D0 Power Management State.
.RE
.IP
.I "Configured by the utility during operation, utility set them to their original"
.I "state after receiving the results:"
.RS
.IP \[bu] 3
The ASPM must be disabled in both the Downstream Port and Upstream Port;
.IP \[bu]
The Hardware Autonomous Speed Disable bit of the Link Control 2 register must be Set in both the
Downstream Port and Upstream Port;
.IP \[bu]
The Hardware Autonomous Width Disable bit of the Link Control register must be Set in both the
Downstream Port and Upstream Port.
.RE
.SH DESCRIPTION
.B pcilmr
utility allows you to take advantage of the PCIe Lane Margining at the Receiver
capability which is mandatory for all Ports supporting a data rate of 16.0 GT/s or
higher, including Pseudo Ports (Retimers). Lane Margining at Receiver enables system
software to obtain the margin information of a given Receiver while the Link is in the
L0 state. The margin information includes both voltage and time, in either direction from
the current Receiver position. Margining support for timing is required, while support
for voltage is optional at 16.0 GT/s and required at 32.0 GT/s and higher data rates. Also,
independent time margining and independent voltage margining is optional.

Utility allows to get an approximation of the eye margin diagram in the form of a rhombus
(by four points). Lane Margining at the Receiver capability enables users to margin PCIe
links without a hardware debugger and without the need to stop the target system. Utility
can be useful to debug link issues due to receiver margins.

.B pcilmr
requires root privileges (to access Extended Configuration Space), but during our testing
there were no problems with the devices and they successfully returned to their normal initial
state after the end of testing.

.SH RESULTS GRADING
The PCIe specification provides reference values for the eye diagram, which are also used by the
.B pcilmr
to evaluate the results, but it seems that it makes sense to contact the
manufacturer of a particular device for references.

The utility uses values set in PCIe Base Spec Rev. 5.0 Section 8.4.2 as the default eye width and height
minimum references. Recommended values were taken from
the PCIe Architecture PHY Test Spec Rev 5.0 (Transmitter Electrical Compliance).

Reference grading values currently used by the utility are presented in the table below:

.TS
box tab(:);
C | Cb S | Cb S
C | Cb | Cb | Cb | Cb
Lb | C | C | C | C.
\&:16 GT/s (Gen 4):32 GT/s (Gen 5)
\&:EW:EH:EW:EH
_
Min:T{
18.75 ps
.br
30% UI
T}:15 mV:T{
9.375 ps
.br
30% UI
T}:15 mV
_
Rec:T{
23.75 ps
.br
38% UI
T}:21 mV:T{
10.157 ps
.br
33% UI
T}:19.75 mV
.TE

.B pcilmr
uses full eye width and height values to grade lanes. However, it is possible that
device supports only one side margining. In such cases by default utility will
calculate EW or EH as a double one side result.

If info for specific device is available, you can configure grading criteria
and tweak utility behavior in one-side only cases for your device using
.I \-g
link specific option (see below).

.SH HARDWARE QUIRKS SUPPORT

Thanks to testing or directly from the manufacturer's documentation, we know that
some devices require special treatment during the margining.
Utility detects such devices based on their Vendor ID \(en Device ID pair.
Right now the list of special devices is hardcoded in
.I margin_hw
file. For such devices utility can automatically adjust port margining parameters
or grading options.

For example, for Ice Lake CPUs RC ports
.B pcilmr
will change device MaxVoltageOffset value and will force the use of
.RI ' "one side is the whole" "' grading mode."

.SH OPTIONS
.SS Device Specifier
.B "You can specify Downstream or Upstream Port of the Link."
.TP
.B "<device/component> \t"
.RI [ "<domain>" :] <bus> : <dev> . <func>
(see
.BR lspci (8))
.SS Utility Modes
.TP
.BI \-\-margin " <downstream component> ..."
Margin selected Links.
.TP
.B \-\-full
Margin all ready for testing (in a meaning similar to the
.B \-\-scan
option) Links in the system (one by one).
.TP
.B \-\-scan
Scan for Links with negotiated speed 16 GT/s or higher. Mark "Ready" those of them
in which at least one of the Link sides have Margining Ready bit set meaning that
these Links are ready for testing and you can run utility on them.
.SS Margining Common (for all specified links) options
.B \-c
Print Device Lane Margining Capabilities only. Do not run margining.
.TP
.BI \-e " <errors>"
Specify Error Count Limit for margining.
.br
Default: 4.
.TP
.BI \-o " <directory>"
Save margining results in csv form into the specified directory. Utility
will generate file with the name in form of
.RI "\[dq]lmr_" "<port>" "_Rx" # _ <timestamp> ".csv\[dq]"
for each successfully tested receiver.
.TP
.BI \-d " <time>"
Specify dwell time in seconds for the margining step.
.br
Default: 1 s
.SS Margining Link specific options
.TP
\fB\-l\fI <lane>\fP[\fI,<lane>...\fP]
.R Specify lanes for margining.
.br
Remember that Device may use Lane Reversal for Lane numbering. However, utility
uses logical lane numbers in arguments and for logging. Utility will automatically
determine Lane Reversal and tune its calls.
.br
Default: all link lanes.
.TP
\fB\-r\fI <recvn>\fP[\fI,<recvn>...\fP]
Specify Receivers to select margining targets.
.br
Default: all available Receivers (including Retimers).
.TP
.BI \-p " <parallel_lanes>"
Specify number of lanes to margin simultaneously.
.br
According to spec it's possible for Receiver to margin up to MaxLanes + 1
lanes simultaneously, but during testing, performing margining on several
lanes simultaneously led to results that were different from sequential
margining, so this feature requires additional verification and
.I \-p
option right now is for experiments mostly.
.br
Default: 1.
.PP
.B "Use only one of \-T/\-t options at the same time (same for \-V/\-v)."
.br
.B "Without these options utility will use MaxSteps from Device"
.B "capabilities as test limit."
.TP
.B \-T
Time Margining will continue until the Error Count is no more
than an Error Count Limit. Use this option to find Link limit.
.TP
.BI \-t " <steps>"
Specify maximum number of steps for Time Margining.
.TP
.B \-V
Same as
.I \-T
option, but for Voltage.
.TP
.BI \-v " <steps>"
Specify maximum number of steps for Voltage Margining.
.TP
\fB\-g\fI <recvn>\fPt=\fI<criteria>\fP{%|ps}\fR[\fP,f\fR]\fP
.TP
.IB "   <recvn>" t=f\fR[\fP, "<criteria>" "{%\fR|\fPps}\fR]\fP"
.TP
.IB "   <recvn>" v= "<criteria>" "\fR[\fP,f\fR]\fP"
.TP
.IB "   <recvn>" v=f\fR[\fP, "<criteria>" \fR]\fP
Specify pass/fail grading criteria for eye width (timing \-t) or height
(voltage \-v) for one of the link receivers. For EW you must choose one of the
units (% UI or ps), for EH mV is used.
.br
Additional flag
.I f
is for situations when port doesn't support two side independent
margining. In such cases by default utility will calculate EW or EH as a
double one side result. You can add
.I f
flag for
.I \-g
option to tell the utility that the result in one direction is actually the
measurement of the full eye and it does not need to be multiplied. This is so called
.RI ' "one side is the whole" "' grading mode."

.SH EXAMPLES
Utility syntax example:
.RS
.BI "pcilmr \-o " "csv ab:0.0 " "\-r " "1,6 " "\-g " "1t=20% " "\-g " "1v=f,30 52:0.0 " "\-l " "0,1,2 " "\-TV"
.RE

.UR https://gist.github.com/\:bombanya/\:f2b15263712757ffba1a11eea011c419
Examples of collected results on different systems.
.UE

.SH SEE ALSO
.nh
.BR lspci (8),
.B PCI Express Base Specification (Lane Margining at Receiver)
.hy